Advertising Disclosure
10 Best 3d Printer Controllers - Holiday Sale
Best Choice01BIGTREETECHBIGTREETECH SKR 3 EZ Control Board 32bit New Upgrade Silent Board Support EZ2209/ EZ5160/ EZ2130 Stepper Driver Compatible TFT Series Touch Screen, DIY for Most FDM 3D Printer (with 5PCS EZ2209)
Free ShippingMain highlights- Why use EZ Drivers? Because 40% of users have damaged the driver due to the wrong installation. It will damage the control board or even more damage. Using EZ Drivers can improve the experience of more users
- SKR 3 EZ’s numerical control fan realizes 24V, 12V, 5V voltage selection through the external power supply module, eliminating the need for the operation of the customer's external transformer module, thereby reducing the probability of damage to the motherboard
- SKR 3 EZ mainboard using 32-bit ARM Cortex-M7 series STM32H743VI main control chip with a main frequency of 480MHz, the performance has greatly improved. It reserves the BOOT button, users can update the motherboard boot program through DFU
- SKR 3 EZ 3D Control Board adopts two kinds of driver sockets, which are compatible with both BIGTREETECH EZ series driver modules and TMC series driver modules. Each motor drive module can select the corresponding motor voltage through the jumper cap
- EZ Drivers can achieve quietness when the motor is locked and running at low speed. It is recommended to select when the maximum motor speed is lower than 300RPM; it can achieve quietness and low power consumption in a wide range of speed and torque. It is recommended that the maximum motor speed exceeds 300RPM Select at 300RPM
9.7Exceptional
Show more
- Curious about how we select the top products for you? Explore How It Works
Value for Money02BIGTREETECHBIGTREETECH Manta M8P V2.0 Integrated Control Board 32Bit Support Klipper, High Speed 3D Printer Silent Motherboard, Compatible TMC5160T Plus,TMC5160,TMC2209,TMC2240 Stepper Driver (Without CB1)
Free ShippingMain highlights- The thermistor can select the pull-up resistance value through the jumper, which supports PT1000 without external modules, which is convenient for DIY use; the control board reserves a three-way four-wire fan interface, which can be used to connect a water cooling device
- The power chip of Manta M8P integrated main control board adopts TPS5450-5A, which supports DC12/24V power input; the output current of this chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry-Pi
- The control board and the core board use BTB connection method, so that other core board solutions other than CM4 can be selected, such as BIGTREETECH CB1. The mainboard reserves the SPI expansion interface for using the Klipper firmware to connect an external acceleration sensor for acceleration compensation
- The MCU firmware can be upgraded through SD card, or through DFU through Klipper's make flash command; the main board reserves the proximity switch interface, supports NPN and PNP type selection, (24V, 12V, 5V) voltage optional, shared with VFAN6 Voltage selection
- BIGTREETECH Manta M8P V2.0 Control Board uses 32-bit ARM Cortex-M7 series STM32H723ZET6 main control chip with a core frequency of 550MHz. High efficiency MOSFET for less heat generation
9.4Excellent
Show more
- 03BIGTREETECH
BIGTREETECH SKR Mini E3 V3.0 Control Board with TMC2209 UART Stepper Driver New Upgrade 32Bit 3D Printer Silent Board for Ender 3, Ender3 Pro, Ender-3 V2 3D Printer
Free ShippingMain highlights- USB Micro B: The PC communication USB interface is upgraded from Mini USB to Micro USB B, which is more adaptable
- Three CNC Fan: Increase the heat dissipation controllable fan to reduce the printer temperature when the device is working
- Output Power Supply: Increase SPI output port +3.3V power supply, external SPI sensor power supply voltage +3.3V and +5V are optional, support the motherboard to directly supply power to peripherals
- Main Control Chip: Adopt STMicroelectronics' latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6
- Increased Heat Sink: Redesign the drive heat sink, strengthen the drive heat dissipation capacity, and greatly improve the heat dissipation performance
9.3Excellent
Show more
- 04BIGTREETECH
BIGTREETECH SKR Pico V1.0 Controller Board Perfectly Compatible with Voron V0.1 3D Printer, Fits Raspberry Pi Using Klipper Firmware, Entry-Level 4-axis DIY Motherboard
Free ShippingMain highlights- Using Raspberry-Pi ARM Cortex-M0+ main control RP2040 microprocessor. This controller board onboard UART mode of TMC2209 and supports Klipper firmware
- ID design is newly upgraded. It adopts the Raspberry Pi board frame, which is perfectly installation with Rasberry-Pi to save internal space. The appearance and performance coexist. It is the coolest choice for Voron players
- Fuse adopts the form of fuse holder + fuse, which is easy to disassemble; the lateral design of the main control board seat perfectly matches the space characteristics of Voron V0 machine that needs to fix the main board vertically
- Chip capacitors (MLCC) of the main control board are all Murata capacitors; well-known brand capacitors, with guaranteed quality and better experience
- BIGTREETECH SKR Pico V1.0 main control board heat sink design is newly upgraded, the heat dissipation area is enlarged, and the heat dissipation performance is greatly improved, which is both beautiful and practical
9.0Excellent
Show more
- 05YWBL-WH
3D Printer Controller, 32 Bit Control Board 3D Printer Control Board Kit Integrated Mainboard Controller, 3D Printer Controllers (Separate Mainboard Model)
Main highlights- Quick Heat Dissipation: This 3D printer control board uses MOSFET for better heat dissipation, 12 to 24V power input, reducing the heating bed current by 1/4, effectively solving the Mosfet heating problem.
- Main Purpose: The integrated mainboard controller is plug and play on for Ender series printers with the BTT SKR MINI E3 V3.0 control board.
- Easy Upgrade: The 3D printer mainboard controller can be easily upgraded with firmware via storage card, with high speed module, access to the to achieve remote printing. It supports setting the stepper drive current in the config file, so you no longer have to worry about adjusting the current to burn the mainboard.
- Custom Command Button: You can design your own boot logo and all buttons, at least 15 command buttons can be customised, you can design your own boot logo and all buttons. Support for breakpoints, power saving, power failure detection, automatic shutdown, etc.
- 3D Printer Control Board: The 3D printer control board uses a 32 bit high speed ARM chip and the self developed main board.
8.9Very Good
Show more
- 06BIGTREETECH
BIGTREETECH TFT35 V3.0.1 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
Free ShippingMain highlights- Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode
- Serial port screen mode supports two printing modes: SD card and U disk
- Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON)
- Reserve WIFI port, and WIFI function is realized by external WIFI module
- 2 sets of UART serial port extension ports are reserved for DIY use
8.8Very Good
Show more
- 07YOUYOUTE
Youyoute Mini Heater for 3D Printer, Resin 3D Printer Temperature Controller 100W Heating Thermostat Temp Control for LCD DLP 3D Printers
Free ShippingMain highlights- Use for: Resin 3D printer mini heater designed for Resin 3D printers, it is small but powerful, for use in cold weather. It helps you to heat up the resin and rise the ambient temperature. Make your 3D printer work well, save your time and Resin material.
- Small Size: Our 3D printer heater is compact, measuring 10.8 x 5.7 x 3.2 cm (4.25 x 2.24 x 1.25 inches) and weighing 117 grams. It is perfect for 8-15 inch resin 3D printers. The heater can raise the temperature from 40°F to 80°F in just 10 minutes, making it ideal for use in cold weather.
- Professionally manufactured: Our 3D printer heater built-in high-precision industry temperature sensor, accurate to 0.1 ℃. Fireproof case, high-quality power cord, all professionally designed for your safe printing.
- Professional design: Our heater is designed for long-term working, capable of running continuously 24/7. The PCB is dual-sided and wiring are professionally engineered to ensure an exceptionally long service life.
- Our heater is equipped with buttons to set the target temperature ( from 10°C to 50°C). The optimal heating temperature for resin being 30°C. Some other heaters default to cooling at 25°C and do not allow target temperature adjustments.
8.7Very Good
Show more
- 08ANYCUBIC
ANYCUBIC Air Purifier & Heat Set, Pre-heatable Temperature Controller for Most LCD/SLA/MSLA Resin 3D Printers, Orginal Accessory Replacment for Photon Mono M5s / M5s Pro, Photon M3 Max, Photon Mono 4
Free ShippingMain highlights- Safe and Reliable: The cover of mini heater&purifer is made of engineering-grade fireproof material that has been tested at 0°C and under continuous operation in actual environment, ensuring safe and long-lasting operation in harsh environment.
- Higher Print Success Rate: The preheat function can raise the temperature to 40°C and hold the resin temperature at 20°C or more before 3D printing. It takes 30 minutes to raise the temperature to the right temperature in an environment with temperatures above 10℃.
- Comfortable Printing Environment: Built-in replaceable activated carbon cartridge reduces resin odour and creates a comfortable printing environment. And purification function can be used separately.
- 2 in 1 Funtion: Anycubic Mini Purifier&Heater combines preheating and purification functions in one unit, provides independent control, easy installation, mini size suitable for most resin printers in cold weather, improves print success rate
8.6Very Good
Show more
- 09KIMISS
KIMISS MKS Controller Board for 3D Printer, Motherboard with Power TVS Protection & Virtual USB Support, 3D Printer Mainboard Module, Desktop Printer Controller
Free ShippingMain highlights- ※【Virtual USB Support】 Supporting virtual USB devices and standalone serial ports (UART3), this MKS controller board allows flexible connectivity via USB drives or memory cards. Firmware customization (e.g., USB_FLASH_DRIVE_SUPPORT) enables seamless file transfers for hassle-free printing.
- ※【Reliable TVS Protection】 The integrated TVS protection on power input safeguards your 3D printer module from voltage spikes, offering high transient power and low leakage current. This feature extends the lifespan of your machine while preventing damage from power fluctuations.
- ※【Powerful Performance Upgrade】 This 3D printer motherboard features an upgraded STM32F407VET6 microcontroller (168 MHz) with 512KB Flash, delivering faster and smoother printing performance. Ideal for replacing older 3D printer controller boards, it ensures compatibility with most machines by simply adjusting firmware settings.
- ※【Enhanced Anti-Interference】 Equipped with advanced anti-interference technology, this 3D printer mainboard maintains stable operation even in noisy environments. The Schottky diode in temperature/MOS circuits reduces voltage drop and improves switching efficiency, ensuring precise control during printing.
- ※【Compact & Portable Design】 Designed for convenience, this 3D printer motherboard is lightweight and space-saving. Its compact size makes it easy to store or carry as a backup, for users who need a portable replacement or upgrade solution.
8.3Good
Show more
- 10Makacces
3D Printer Enclosure with Ventilation, 12V Fan Adjustable Airflow, Resin 3D Printer Vented Enclosure,Fireproof, UV Block,Compatible with Bambu Lab Creality Anycubic Elegoo Series LCD Resin 3D Printer
Free ShippingMain highlights- UV Light Protection for Resin Materials. This enclosure includes a UV light shelter with a brown window that blocks most UV rays, preventing premature curing of your resin materials. By safeguarding your materials from UV exposure, the enclosure ensures the integrity of your prints throughout the entire process, providing consistent results and protecting resin quality.
- The Makacces Resin 3D Printer Enclosure is made from fire-resistant fabric, ensuring reliable performance during printing. It helps maintain a consistent temperature, improving print quality and reducing print failures. Compatible with both LCD and FDM printers, this enclosure creates an ideal environment for smooth and successful 3D printing projects.
- Smoke and Odor Extraction for Cleaner Air. The Makacces 3D Printer Enclosure features an effective smoke and odor extraction system, ensuring a cleaner and more comfortable printing environment. It eliminates fumes generated during the printing process, improving air quality in your workspace. With this feature, you can focus on your projects without worrying about lingering odors or harmful emissions.
- Easy Setup and Durable Construction. Built with a sturdy stainless steel frame, the Makacces 3D Printer Enclosure is both lightweight and durable. Its dimensions (25" x 21" x 29.5") make it compatible with most LCD and FDM printers. The kit includes a pre-installed fan, ventilation pipe, and high-quality zipper for easy assembly and use. Plus, with included tool and storage bags, your workspace stays organized and clutter-free.
- Advanced Ventilation with Adjustable Fan Speed. Equipped with a 12V fan and adjustable speed controller, the enclosure efficiently vents fumes and smoke while printing. The fan’s speed control allows you to fine-tune airflow to meet your needs, ensuring optimal ventilation. It helps maintain a clean and fresh workspace, reducing the impact of harmful fumes on your prints and the environment.
8.2Good
Show more
